Question 1
Which two major areas can be used when discussing the high-level overview
of a typical enterprise network? Choose two.
Campus
backbone
|
|||||
Building
distribution
|
|||||
Building
access
|
|||||
Enterprise
campus
|
|||||
Enterprise
edge
|
|||||
Question 2
Which of the following is used when choosing a dynamic routing protocol?
Choose two.
Cost of
equipment
|
|||||
Knowledge level of a specific routing protocol
|
|||||
Scalability
|
|||||
Vendor
support
|
|||||
Type of
links supported
|
|||||
Question 3
BGP is which type of protocol?
Distance
vector
|
||||
Advanced
distance vector
|
||||
Link-state
|
||||
Path
vector
|
||||
Question 4
Which two factors can influence convergence time for a routing protocol?
Choose two.
Fine tuning routing protocol timers
|
||||
Size of the routing table
|
||||
Configuring
route summarization
|
||||
Type of link between routers
|
||||
Question 5
Scalability of a network includes which two factors? Choose two.
Number of
adjacent neighbors
|
||
Number of
routers
|
||
Distance
between routers
|
||
Ability to do auto summarization
|
||
Question 6
Which of the following traffic types is not supported by IPv6?
Unicast
|
||
Multicast
|
||
Anycast
|
||
Broadcast
|
||
Question 7
What is the IPv6 multicast address used by EIGRP?
FF02::5
|
|
FF02::6
|
FF02::9
|
||
FF02::A
|
||
Question 8
Which type of IPv6 address is used by routing protocols for communications
only on the link?
Unique
local
|
||
Site local
|
||
Link-local
|
||
Multicas
|
||
Question 9
Which type of ICMPv6 message is sent by a device to request information
about the network such as the prefix, prefix length and default gateway?
Neighbor
Advertisement
|
||
Neighbor
Solicitation
|
||
Router
Advertisement
|
||
Router
Solicitation
|
||
Question 10
Which type of ICMPv6 message is sent by a device to inform another device
of its IPv6 address and associated Ethernet address?
Neighbor
Advertisement
|
||
Neighbor
Solicitation
|
||
Router
Advertisement
|
||
Router
Solicitation
|
||
Question 11
Which type of network allows access to multiple devices on the same network
but does not provide broadcast capabilities?
Point-to-point
|
||
Broadcast
|
||
NBMA
|
||
Multi-access
|
||
Question 12
Which type of subinterface provides connections similar to physical
point-to-point links and has no neighbor discovery issues?
Point-to-point
|
||
Point-to-multipoint
|
||
Multipoint
|
||
All of the
above
|
||
Question 13
Which tunneling protocol was developed by Cisco to encapsulate a Layer 3
protocol inside a point-to-point, tunnel-over-IP network?
GRE
|
||
DMVPN
|
||
IPsec
|
||
MPLS
|
||
Question 14
A Layer 3 MPLS VPN over GRE is an example of what type of VPN?
DMVPN
|
||
Multi-VPN
|
||
Combination
VPN
|
||
Hybrid VPN
|
||
Question 15
What is the main benefit of a GRE tunnel in respect to routing protocols?
Strong
security
|
||
Supports
IP multicast
|
||
Stateless
|
||
Low
overhead
|
||
Question 16
What protocol is used by routers to determine the next-hop IP address in
tunneling networks?
Dynamic
GRE
|
||
NHRP
|
||
mGRE
|
||
MPS
|
||
Question 17
What framework of open standards that provides confidentiality, data
integrity, authentication and anti-replay protection?
IPsec
|
||
VPN
|
||
PAP
|
|
PSK
|
Question 18
R1 has an adjacent RIPng neighbor R2. R1 has a LAN with no neighbors, 2001:DB8:ACAD:1::/64.
R1 advertises this prefix to adjacent RIPng neighbor, R2. What metric does R2
display for 2001:DB8:ACAD:1::/64?
1 hop
|
||
2 hops
|
||
3 hops
|
|
4 hops
|
Question 19
How is an interface enabled for RIPng?
Using the network prefix/prefix-length router mode command
|
||
Using the ipv6 router rip name interface command
|
||
Interfaces are automatically enabled for RIPng when the RIPng process is
started
|
||
Using the router ripng name interface command
|
||
Question 20
Router R1 has multiple routes in its routing table including RIPng routes,
directly connected networks and a static default route. R2 receives a static
default route from R1 but no other routers. This is because R1 uses which
option at the end of ipv6 rip name default-information interface
command?
static
|
||
originate
|
||
default-only
|
||
only
|
||
Question 21
Refer to
the exhibit. RIPng has been configured on all routers in the network but the
routers do not receive RIP routing updates. What could be done to remedy
the problem?
Configure the RIPng version 2 under the routing protocol configuration.
|
||
Configure IPv4 addresses for the interfaces that are participating in the
routing process.
|
||
Issue the command ipv6 rip LAB enable for the interfaces that are
participating in the routing process.
|
||
Configure the network statement under the routing protocol configuration.
|
||